install the NetBackup sg driver and the Sun st driver

Installing/reinstalling the sg and the st drivers

Description

You must install the NetBackup sg driver and the Sun st driver on each Solaris NetBackup media server that hosts tape devices.

Each time you add or remove a device, you should configure the NetBackup sg driver and the Sun st driver again. For 6 GB and larger serial-attached SCSI (SAS) HBAs, also configure class 08 and 0101 for the sg driver.

See Configuring 6 GB and larger SAS HBAs in Solaris.

Before you configure the sg and the st drivers, ensure that all devices are turned on and connected to the HBA.

The sg.build command uses the Solaris sasinfo command to probe for SAS attached device paths. This command is only available on Solaris 11 and later. On Solaris 10 and earlier, you must configure the sg driver manually.

 

To install and configure the sg and the st drivers

  1. Invoke the following two commands to run the NetBackup sg.build script:

     

    cd /usr/openv/volmgr/bin/driver
    /usr/openv/volmgr/bin/sg.build all -mt target -ml lun

     

    The following describes the options:

    •  

      The all option creates the following files and populates them with the appropriate entries:

      • /usr/openv/volmgr/bin/driver/st.conf

      • /usr/openv/volmgr/bin/driver/sg.conf

      • /usr/openv/volmgr/bin/driver/sg.links

    • The -mt target option and argument specify the maximum target ID that is in use on the SCSI bus (or bound to an FCP HBA). The maximum value is 126. By default, the SCSI initiator target ID of the adapter is 7, so the script does not create entries for target ID 7.

    • The -ml lun option and argument specify the maximum number of LUNs that are in use on the SCSI bus (or by an FCP HBA). The maximum value is 255.

  2. Replace the following seven entries in the /kernel/drv/st.conf file with all of the entries from the /usr/openv/volmgr/bin/driver/st.conf file:

     

    name="st" class="scsi" target=0 lun=0;
    name="st" class="scsi" target=1 lun=0;
    name="st" class="scsi" target=2 lun=0;
    name="st" class="scsi" target=3 lun=0;
    name="st" class="scsi" target=4 lun=0;
    name="st" class="scsi" target=5 lun=0;
    name="st" class="scsi" target=6 lun=0;

    You should make a backup copy of the /kernel/drv/st.conf file before you modify it.

  3. Reboot the system with the reconfigure option (boot -r or reboot — -r).

    During the boot process, the system probes all targets in the st.conf file for devices. It should create device files for all of the devices it discovers.

  4. Verify that Solaris created the device nodes for all the tape devices by using the following command:

    ls -l /dev/rmt/*cbn

  5. Install the new sg driver configuration by invoking the following two commands:

     

    /usr/bin/rm -f /kernel/drv/sg.conf
    /usr/openv/volmgr/bin/driver/sg.install

     

    The NetBackup sg.install script does the following:

    • Installs and loads the sg driver.

    • Copies the /usr/openv/volmgr/bin/driver/sg.conf file to /kernel/drv/sg.conf.

    • Creates the /dev/sg directory and nodes.

    • Appends the /usr/openv/volmgr/bin/driver/sg.links file to the /etc/devlink.tab file.

  6. Verify that the <command>sg</command> driver finds all of the robots and tape drives.

 

Terms of use for this information are found in Legal Notices.

netbackup77_deviceconfig_guide

Read more

How to migrate Raspberry Pi 5 OS from micro SD to NVME m.2 SSD

首先我買了Raspberry Pi CM5後來買了Raspberry Pi CM5 I/O board來當個人電腦使用,系統是安裝在256GB SD卡上運行的很好。用久了在開啟較肥的程式像Web Browser或LiberOffice會有慢半拍的反應,而有了升級NVME m.2 SSD念頭。 因為Raspberry Pi 5支援的最快PCIe gen3 x 4就不去考慮快的Gen4 or Gen5 m.2 SSD。找了ADATA出的 LEGEND 710入門級的產品,會利用HMB(Host Memory Buffer)來加速I/O速度,因為是Raspberry Pi OS kernel會認不得而無法正常使用 事先在SD卡的/boot/firmware/cmdline.txt 加入 kernel command line參數如下,然後重開機m.

By Phillips Hsieh

How to document Home Lab and Network

運維機房和跨域的網路,會遇到各式需求與問題,用對工具才能分析問題,個人覺得最重要的是使用能處理問題的工具。 推薦目前想學和正在使用的平台與軟體,協助將公司/家用機房文件化 佈告欄任務管理 Focalboard 白板可管理任務指派 網路架構文件編寫 netbox 精細管理網路設備與連接線路 IP 資源管理 phpipam 專注網路IP分配 邏輯塊文件編寫 draw.io 視覺化概念圖 機房設備管理 ITDB 管理設備生命週期與使用者

By Phillips Hsieh

如何在Raspberry Pi4上安裝Proxmox for ARM64

第一步 準備好Raspberry Pi 4 / CM4 4GB RAM,這裡要留意CM4如果是買有內建eMMC storage會限制不能使用SD卡開機而限制本地空間容量,如果沒有NAS外接空間或使用USB開機的話,建議買CM4 Lite插上大容量SD卡 第二步 去Armbian官網下載最小化Debian bookworm image https://www.armbian.com/rpi4b/ Armbian 25.2.2 Bookworm Minimal / IOT 然後寫入SD/USB開機碟,寫入方法參考官方文件 https://github.com/raspberrypi/usbboot/blob/master/Readme.md Note: 官方提供的預先設定系統方法,可以在Armbian初次啟動自動化完成系統設定。連結在此 https://docs.armbian.com/User-Guide_Autoconfig/

By Phillips Hsieh

世界越快心越慢

在晚飯後的休息時間,我特別享受在客廳瀏灠youtube上各樣各式創作者的影音作品。很大不同於傳統媒體,節目多是針對大多數族群喜好挑選的,在youtube上我會依心情看無腦的動畫、一些旅拍記錄、新聞時事談論。 尤其在看了大量的Youtube的分享後,我真的感受到會限制我的是我的無知,特別是那些我想都沒想過的實際應用,在學習後大大幫助到我的生活和工作層面。 休息在家時,我喜歡想一些沒做過的菜,動手去設計生活和工作上的解決方案,自己是真的很難閒著沒事做。 如創作文章,陪養新的習慣都能感覺到成長的喜悅,是不同於吃喝玩樂的快樂的。 創作不去限制固定的形式,文字是創作、影像聲音也是創作,記錄生活也是創作,我想留下的就是創造—》實現—》回憶,這樣子的循環過程,在留下的足跡面看到自己一路上的成長、失敗、絕望、重新再來。 雖然大部份的時候去做這些創作也不明白有什麼特別的意義,但不去做也不會留下什麼,所以呀不如反事都去試試看,也許能有不一樣的水花也許有意想不到的結果,投資自己永遠不會是失敗的決定,不是嗎?先問問自己再開始計畫下一步,未來沒人說得準。 像最近看youtube仍大一群人在為DOS開

By Phillips Hsieh